Model
DS200 - Double Metal
Sheet Detector |
Features
- Pulsed Electromagnetic
does not hold on to metal blank or sheet
- Single metal thickness ranges
.25 mm to 6.0 mm (.01 “ to .240”)
- Four Probe Diameters
36mm, 42mm, 54mm, 75mm SELECT
- Metal Present Output
transistor (PnP) output when metal present
- Proximity Detector
built in proximity probe
to detect metal, last sheet
- Push-Button
Calibration
instantaneously measure thickness, calculates reject
threshold
- Teach
with a single sample or two sample,
- Fast Response to Double Detection
- Diagnostic
Warning
alternately flashing lights for
error and probe failure, fail safe output
- Power
Input
Range 100 to 240 VAC @ 50-60
Hz 20 w
Quick
Connect
terminals for fast replacement
and to reduce downtime
- Contact
Relay output rated at 10 AMPS (½ HP) @240VAC,
8 AMPS @24 VDC.
- Works
with all Prime PE Model probes
SPECIFICATIONS |
 |
Model
DS200 |
 |
Model
PE42 |
|
| Prime’s
Model DS200 Single Probe Double Metal Sheet
Detector is installed in difficult locations
where sensing is only possible on one side.
It detects ferrous metals over a thickness
range of .25 mm to 6.0 mm (.01” to .240”
). The DS200 measures the change in it’s magnetic
field as metal is in contact with it's face. A new
sensing element in the probe head increases
sensitivity and improves stability compared
to other brands. To calibrate, simply insert
a sheet in front of the probe and push the
calibrate button. The detector automatically
sets the reject threshold above the single
sheet reading. It’s
form “C” contact relay de-energizes if a double
is detected, power is lost or a probe failure
is detected. One additional PNP transistor
output turns on when metal is detected.
This metal output is applied (including doubles) to a good sheet
counter, jam detector or last sheet detect
circuit. The Model DS200 detector has fault
detection that immediately analyzes any problem
and operates a blinking Green LED code that
directs the operator or maintenance department
to the problem. |
Power
input: |
Ranges from
100 Volts to 240 Volts AC Max, 50 to
60 Hz,
at 20 Watts |
| Output
Response |
<
140 mSec. w/PE36 to <250mSec w/PE75 |
| Outputs: |
SPDT
contact relay Double detected, NC closed
Max. load 10 Amps @ 240 Vac, 8 Amps @ 24 V
dc ½ HP @ 240 V ac |
| Metal
Present Output: |
PNP transistor, sourcing 24 Volts dc,
100mA max.
Metal detected= 24
V dc,
No metal = 0 V dc
|
| Output
fail Safe: |
Contact
goes to double condition. Metal Present output turns off, indicating no metal present. |
| Metal
Sensitivity: |
Ferrous
metal, steel, tinplate |
| Calibration: |
Push-button
switch with single sheet or two sample teach for fine accuracy |
| Sample
Indicators: |
Green
for single, amber for double, green blinking
probe is bad or disconnected |
| External
inputs: |
Calibrate & output latched reset |
| Sensor
Operation: |
magnetic flux field generated by a quick electromagnetic pulse is shunted across sensor
poles by the thickness of metal. Maximum thickness
is limited by the diameter of the probe. The
chart below provides a range for each probe. |
Probe Model |
Probe Diameter |
Breakaway Force |
Min. Thickness |
Max. Thickness |
| PE36 |
36mm (1.42") |
<1 lb. |
0.25mm (.01") |
2.3mm (0.09") |
| PE42 |
42mm (1.65") |
<1 lb. |
0.25mm (.01") |
3.6mm (0.14") |
| PE54 |
54mm (2.13") |
<1 lb. |
0.25mm (.01") |
4.6mm (0.18") |
| PE75 |
75mm (2.95) |
<1 lb. |
0.25mm (.01") |
6.0mm (0.24") |
|
 |
 |
|
| |
|
| Additional
Product Information
|
|
|
|
|
